Smart Drip Irrigation Kit - ISE User Manual

SCENARARIOS

Green LED flashing

The device is working normally. 

Green LED always on

The device is connecting with bluetooth.

Green LED fast flashing

The firmware of the device is being upgraded.

Red LED always on

The device is malfunctioning. Usually the filter is above water surface, or the pump is blocked. 

Red LED flashing

The network is abnormal during remote connection. 

Installation Step

1.Install the Drip Irrigation Kit①in a appropriate position. It can be secured with nano-adhesive paper and clips on the back of the device.Please place your LetPot device in the location covered by the wifi signal.

Hello

2.Cut a piece of the hose② and link one of the end to the filter⑥. Then place the filter in the water tank or storage container(warn: pay attention to the water line above the filter). Next, link the other end to the water inlet “IN” that below the device.And add clips at the connection between the water pipe and the inlet and outlet.

Hi

3.Cut a appropriate length of hose to link the device and the first pot together. One end of the hose should be installed at outlet “OUT”,and the other end is linked Tee Connector④. Then we need one more hose to connect the other side of the Tee Connector④ to Adjustable Dripper. Next, Water Pipe Bracket is used to make sure that the hose is securely anchored in the range of the pot(you can insert it into the soil to fix the position). The remaining end of the Tee Connector④ can be linked to another pot. 

-Is me gain

4.Adjust the front knob of the Adjustable Dripper⑤ to control water output.

-Nothings here

5. Plug the drip irrigation kit to the power supply and connect to the LetPot app via WIFI or bluetooth(accord to the instructions of app)

-Just read title

automatic watering system

FAQ

1.Why the single watering time of the drip irrigation device does not follow the total time that I set.

In order to allow the soil to absorb water gradually, the device will automatically stop for 30 seconds every 30 seconds of watering and then start again. For example, a 2-min task will only water for 1 minute. If you want your plants be watered for 4 minutes, you can set up the 8-min task.

2.After setting the parameters or turning on the switch, the drip irrigation does not start working immediately.

(1)Due to circuit protection or the network problems, sometimes your settings and switches do not take effect immediately, and the device will record and work according to the settings again within 1-3 minutes.
(2) If the device still does not respond, press and hold the [R] button at the bottom of the 

3.The device does not work while you are plugging in the power supply.

(1) Check out your socket has power.
(2) Check out the DC plug whether connects tight enough to the device’s power or not. 

4.Bluetooth does not connect to the device.

(1) Close the phone to the device.
(2) Check out the green light. If it is often light , it means the other phone is connecting. Stuff off the connection or reboot the device is okay.

5.The device fails connection to the WIFI.

(1) Check out the WIFI is 2.4G.
(2) Check out the correct name and password of your WIFI.
(3) Reboot the device and router and try again.
(4) Is the LED of LetPot blinking in red?
The LetPot cannot reach the Wi-Fi router.  You may try configuring a stronger Wi-Fi in Setting. 
(5) Is the phone’s network stable? 
Check if your phone's network is turned on and connected properly. Still, not working? Exit the LetPot App completely and reopen it to retry.

6.How to make the device water immediately.

(1)After setting the parameter on the app, the device will work immediately.
(2)The device begin to water for 3 mins automatically after short pressing the logo button, and stop by pressing again.

7.The red light is often work.

(1)Check out the lack of water or not.
(2)Check out the water line above the filter or not.

8.The water pipe is pushed out or leaking while water.

(1) Open the valve of the Dripper before plugging to the power supply
(2) Because of the large pressure of the pump,you should adjust the valve up to the maximum while you are linking 1-2 drippers, it can balance the water pressure.(3)Check if the clips at the inlet and outlet are tight enough

9.The system will be fine to run nutrients through?

(1)The drip irrigation can pump liquid nutrients, but in order to prolong the service life of the pump, it is recommended to draw clean water after a period of time to rinse the residual nutrients in the pipeline, because the nutrients will produce salt after evaporation.

APP(Bluetooth Mode)

LetPot Drip Irrigation Kit ~ Adding Device (Bluetooth Mode)

APP(WI-FI MODE)

LetPot Drip Irrigation Kit ~ Change to Wi-Fi Mode for remote control

Download Manual

*You can download this manual on drive.google.com
and feel free to contact us if you have any questions: service@letpot.com;